安装维护

正确地使用产品能够获得更佳的产品体验。

FSB带座轴承由于填充优质润滑脂和用高性能的密封圈密封，因此在一 般的运转条件下可以无给油使用。

但是，在运转温度高和尘埃、水较多等相对恶劣的环境中使用时，会使润滑脂劣化，导致润滑不良。需在适当的间隔时间进行定期检查来延长轴承的使用寿命。 

轴承的定期检查是通过检查外观和运转状态来判断带座轴承有无异常。

轴承定期检查发现的主要异常内容及其原因如下表:

定期检查发现的主要异常内容及其原因

异常内容
 原因
扭矩过大 (重)
 1 润滑脂劣化
2 润滑脂补充过多，密封圈和挡圈接触
3 挡圈变形与密封圈接触
4 轴的伸长等产生异常的负荷
有异常音、异常振动

 1 轴承内圈的止动顶丝或轴承座安装螺栓的松动
2 由于蠕变或磨蚀，轴和轴承内圈的配合面磨损
3 轴承内部侵入了异物
4 轴承的滚道面由于滚动疲劳产生损伤
5 负荷过大，轴承的滚道面产生压痕
6 轴的挠曲或弯曲过大
有异常温升

 1 润滑脂劣化
2 润滑脂补充过多，密封圈和挡圈接触
3 挡圈变形与密封圈接触
4 轴承内圈的止动顶丝或锁紧螺母(紧固件)松动
5 轴的伸长等产生异常的负荷
6 轴承的滚道面由于滚动疲劳产生损伤

通过定期检查发现轴承出现异常时，要迅速采取对策并加以实施。及时更换轴承，以免损坏其它零部件及发生重大事故。

润滑脂的补充

FSB带座轴承是供油式的，可根据其使用环境定期补充相同类型的润滑脂，
以保持轴承的正常润滑状态，从而延长轴承的使用寿命。

轴承组件的润滑脂补充间隔推荐表

运转温度°C
 润滑脂补充间隔时间
 使用轴承
>
 ≤
 相当干净
 尘埃多
 尘埃多、飞溅泥
-
 50
 (3个月)
 (2个月)
 (1个月)
 普通型
-
 -
 无给油
 1年
 4个月
50
 70
 1年
 4个月
 1个月
70
 100
 6个月
 2个月
 2周
100
 120
 2个月
 2周
 5日
 耐热型
120
 150
 2周
 5日
 2日
150
 180
 1周
 2日
 1日

带座轴承的润滑脂补充量推荐表

内径型号

 润滑脂补充量，g
直径系列(1)
2
 X
 3
01
 1
 -
 -
02
 1
 -
 -
03
 1
 -
 -
04
 1
 -
 -
05
 1
 1.5
 2.0
06
 1.5
 2.0
 3.0
07
 2.0
 2.5
 3.5
08
 2.5
 3.0
 5.0
09
 3.0
 3.5
 6.5
10
 3.5
 4.5
 8.5
11
 4.5
 6.0
 12
12
 6.0
 7.0
 15
13
 7.0
 8.0
 18
14
 8.0
 10
 22
15
 10
 12
 26
16
 12
 15
 30
17
 15
 18
 35
18
 18
 22
 40
19
 -
 -
 48
20
 25
 30
 62
21
 30
 -
 70
22
 -
 -
 82
24
 -
 -
 99
26
 -
 -
 127
28
 -
 -
 152

注1)轴承的基本型号是，由直径系列后续内径型号构成。

润滑脂的补充是通过安装在轴承座上的注油嘴和注脂枪来进行：  

1、清扫注油嘴及油帽周边，打开油帽后并清扫注油嘴。
2、清扫注脂枪，填充洁净的润滑脂。
[注]：向带座轴承补充润滑脂时，推荐一边用手转动轴（或将带座轴承低速运转）一边进行。这样可以将新的润滑脂均匀地补充到轴承内部。
3、清扫残留在注油嘴及周边的润滑脂，并把油帽重新安装到注油嘴上。

轴承的更换

FSB带座轴承的轴承和轴承座具有互换性；如果轴承出现异常时，可以更换轴承继续使用。

带座轴承的更换过程如下所示：

1、将带座轴承从轴、底座上卸下。

2、拧入止动顶丝使头部低于轴承内圈的外径面。防止轴承拆卸时，止动顶丝的头部与轴承座干涉。

3、用锤子的柄等，将轴承旋转90°置于水平。

4、从轴承座安装槽中取出轴承，将新的轴承按拆卸相反的过程进行安装。

Installation and maintenance

Using the product correctly can get a better product experience.

The FSB seated bearings are filled with high-quality grease and sealed with high-performance seals, so they can be used without oil under normal operating conditions.

However, when used in a relatively harsh environment such as high operating temperature and a lot of dust and water, the grease will deteriorate and cause poor lubrication. Regular inspections are required at appropriate intervals to extend the life of the bearing. 

The periodic inspection of the bearing is to judge whether the bearing with a seat is abnormal by checking the appearance and running state.

The main abnormal contents found in the periodic inspection of bearings and their causes are as follows:

The main abnormal contents found in regular inspections and their causes

Abnormal content
 the reason
Excessive torque (heavy)
 1 Deterioration of grease
2 Too much grease is added, and the sealing ring and the retaining ring contact
3 The retaining ring is deformed and contacts the sealing ring
4 Abnormal load caused by extension of shaft
There are abnormal sounds and vibrations

 1 Looseness of the retaining screw of the inner ring of the bearing or the mounting bolt of the bearing seat
2 The mating surfaces of the shaft and the inner ring of the bearing wear due to creep or abrasion
3 Foreign matter has penetrated into the bearing
4 The raceway surface of the bearing is damaged due to rolling fatigue
5 If the load is too large, the raceway surface of the bearing produces indentation
6 Deflection or bending of the shaft is too large
Have abnormal temperature rise

 1 Deterioration of grease
2 Too much grease is added, and the sealing ring and the retaining ring contact
3 The retaining ring is deformed and contacts the sealing ring
4 The retaining screw or lock nut (fastener) of the bearing inner ring is loose
5 Abnormal load caused by elongation of axis
6 The raceway surface of the bearing is damaged due to rolling fatigue

When an abnormality in the bearing is found through regular inspections, countermeasures must be taken quickly and implemented. Replace the bearings in time to avoid damage to other parts and major accidents.

Replenishment of grease

FSB seated bearings are oil-supplied, and the same type of grease can be regularly replenished according to their use environment
to maintain the normal lubrication state of the bearing, thereby extending the service life of the bearing.

Recommended grease replenishment interval for bearing components

Operating temperature °C
 Grease replenishment interval
 Use bearings
>
 ≤
 Quite clean
 Dusty
 Lots of dust, splashing mud
-
 50
 (3 months)
 (2 months)
 (1 month)
 normal type
-
 -
 No oil
 1 year
 4 months
50
 70
 1 year
 4 months
 1 month
70
 100
 6 months
 2 months
 2 weeks
100
 120
 2 months
 2 weeks
 5th
 Heat resistant type
120
 150
 2 weeks
 5th
 2 days
150
 180
 1 week
 2 days
 1 day

Recommended table of grease replenishment for seated bearings

Inner diameter model

 Replenishment amount of grease, g
Diameter series (1)
2
 X
 3
01
 1
 -
 -
02
 1
 -
 -
03
 1
 -
 -
04
 1
 -
 -
05
 1
 1.5
 2.0
06
 1.5
 2.0
 3.0
07
 2.0
 2.5
 3.5
08
 2.5
 3.0
 5.0
09
 3.0
 3.5
 6.5
10
 3.5
 4.5
 8.5
11
 4.5
 6.0
 12
12
 6.0
 7.0
 15
13
 7.0
 8.0
 18
14
 8.0
 10
 twenty two
15
 10
 12
 26
16
 12
 15
 30
17
 15
 18
 35
18
 18
 twenty two
 40
19
 -
 -
 48
20
 25
 30
 62
twenty one
 30
 -
 70
twenty two
 -
 -
 82
twenty four
 -
 -
 99
26
 -
 -
 127
28
 -
 -
 152

Note 1) The basic model number of the bearing is composed of the inner diameter model following the diameter series.

The replenishment of grease is carried out through the grease nozzle and grease gun installed on the bearing seat:  

1. Clean the oil injection nozzle and the periphery of the oil cap, open the oil cap and clean the oil injection nozzle.
2. Clean the grease gun and fill it with clean grease.
[Note ] : When replenishing grease to the bearing with a block, it is recommended to rotate the shaft by hand (or run the bearing with a block at a low speed). In this way, new grease can be evenly added to the inside of the bearing.
3. Clean the grease remaining in the grease nozzle and surrounding area, and reinstall the grease cap on the grease nozzle.

Bearing replacement

The bearing and the bearing seat of FSB seated bearings are interchangeable; if the bearing is abnormal, the bearing can be replaced and used.

The replacement process of the seated bearing is as follows:

1. Remove the bearing with seat from the shaft and base.

2. Screw in the stopper wire so that the head is lower than the outer diameter of the inner ring of the bearing. Prevent the head of the stop screw from interfering with the bearing seat when the bearing is disassembled.

3. Using the handle of a hammer, etc., rotate the bearing 90° to level it.

4. Take out the bearing from the bearing seat installation groove, and install the new bearing according to the reverse process of disassembly.

我们的专业技术人员会向你提供帮助。受理时间：8:00~18:00（周一~周五，不包括中国法定节假日）

邮件咨询：business@jxc-cn.com

咨询电话：021-59927000 / 59928000

品牌承诺用心之

用心感知

用心感知，是一切创造的起点，也是 JXC践行品牌承诺的第一步。对于每个行业、每位客户的产品应用需求，我们均用心了解，深入沟通，为每位客户提供最适合的应用方案，真正做到以人为本。我们相信，根据行业差异，为客户优化产品方案，是制造业未来发展的最高追求。

用心创造

用心创造，JXC直面全球制造业的挑战，以持续不断的创造应对各行业的复杂性和不确定性，为世界各地的客户提供全面的智能化、信息化产品方案，引领科技推进、挑战极限。JXC针对不同客户的差异化、自主化需求，精心开发、研制特定的产品，用心创造个性化产品，满足行业需求。

用心靠近

用心靠近，是 JXC的终极目标，也是 JXC[用心改变]的最高承诺。我们深知每一个客户的珍贵，以客户为中心，持续创新技术、改进管理，秉承高质量为第一要求的发展理念，不断为客户、社会提供优质的产品、高效的服务及相关解决方案。以品质成口碑、以专业创高效，坚持自我反思，用心靠近需求。

嘉曦轴承（上海）有限公司    技术支持：佰联轴承网